Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 84

Страница: 84 / 2244

1. Confirm by visual inspection that there is no damage to the balancer unit gear and verify that the shaft

turns smoothly.



If there is any damage or malfunction, replace the balancer unit.

2. Install the

SST

as shown in the figure.

Fig. 83: Attaching SST To Balancer

Courtesy of MAZDA MOTORS CORP.

3. Turn the crankshaft clockwise the crankshaft is in the No. 1 cylinder TDC position (until the balance

weight is attached to the

SST

4. Install the adjustment shim to the seat face of the balancer unit.

5. With the balancer unit marks at the exact top center, assemble the unit to the cylinder block.

CAUTION:



Due to the precision interior construction of the balancer unit, it
cannot be disassembled.

2007 Mazda MX-5 Miata Sport

2006-08 ENGINE Mechanical - Overhaul - 2.0L (LF) & 2.3L (L3) - Mazda6 & MX-5 Miata

Microsoft

Thursday, July 09, 2009 2:43:26 PM

Page 84

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы:

Похожие инструкции для MX-5 Miata Sport 2007

Бренды по названию

Популярные бренды

Mazda MX-5 Miata Sport 2007, Руководство пользователя

Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы:

Похожие инструкции для MX-5 Miata Sport 2007

Бренды по названию

Популярные бренды