Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 1405 | Manualshive

Страница: 1405 / 2244

background image

Fig. 5: Exploded View Of Air Distribution Unit Components

Courtesy of MAZDA MOTORS CORP.

2. Assemble in the reverse order of disassembly.

A/C UNIT REMOVAL/INSTALLATION

1. Remove battery cover.

2. Disconnect the negative battery cable. (See

BATTERY REMOVAL/INSTALLATION [LF]

.)

3. Discharge the refrigerant from the system. (See

REFRIGERANT RECOVERY

.) (See

REFRIGERANT CHARGING

.)

4. Drain the engine coolant. (See

ENGINE COOLANT REPLACEMENT [LF]

.)

5. Disconnect from A/C unit in the order in

Fig. 6

.

CAUTION:



If moisture or foreign material enters the refrigeration cycle,
cooling ability will be lowered and abnormal noise or other
malfunction could occur. Always plug open fittings immediately
after removing any refrigeration cycle parts.

2007 Mazda MX-5 Miata Sport

2007 HVAC Basic System - MX-5 Miata

Microsoft

Thursday, July 09, 2009 2:22:45 PM

Page 6

© 2005 Mitchell Repair Information Company, LLC.

«
...
1403
1404
1405
1406
1407
...
»

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MX-5 Miata Sport 2007

Бренд: Daihatsu Страницы: 485

Electronic Parking Disc II

Бренд: Jacob Jensen Страницы: 28

Бренд: NavLinkz Страницы: 4

Бренд: Porsche Страницы: 144

Бренд: Veigel Страницы: 24

Бренд: Cellular Line Страницы: 25

Бренд: Webasto Страницы: 18

Бренд: Opel Страницы: 32

Бренд: Unex Страницы: 30

Бренд: KEKO Страницы: 13

Stealth 4191F Series

Бренд: Road Armor Страницы: 5

Бренд: rockymounts Страницы: 6

Бренд: Volvo Страницы: 10

Бренд: Subaru Страницы: 2

Бренд: Kuda Страницы: 3

Бренд: Magneti Marelli Страницы: 2

Black Bison Sports Series

Бренд: Wald Страницы: 7

Бренд: Kia Страницы: 25

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды