Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 722

Страница: 722 / 2244

Fig. 2: Identifying Proper Cooling System Cap

Courtesy of MAZDA MOTORS CORP.

ENGINE COOLANT PROTECTION INSPECTION [LF]

1. Measure the coolant temperature and specific gravity using a thermometer and a hydrometer.

CAUTION:



Use engine coolant at a concentration that meets the
environmental conditions in which the vehicle is driven,
otherwise engine damage could occur.



The engine has aluminum parts and must be protected by an
ethylene-glycol-based coolant to prevent corrosion and
freezing.



Do not use coolants containing Alcohol, Methanol, Borate or
Silicate. These coolants could damage the cooling system.



Use only soft (demineralized) water in the coolant mixture.
Water that contains minerals will cut down on the coolant's
effectiveness.



Engine coolant damages paint. If engine coolant does get on a
painted surface, rinse it off quickly.

NOTE:



If the "FL22" mark is shown on or near the cooling system cap, use
FL22 type engine coolant.



FL22 type engine coolant is shipped as a diluted solution (55%

2007 Mazda MX-5 Miata Sport

2007 ENGINE Cooling System - MX-5 Miata

Microsoft

Thursday, July 09, 2009 3:06:06 PM

Page 3

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы:

Похожие инструкции для MX-5 Miata Sport 2007

Бренды по названию

Популярные бренды

Mazda MX-5 Miata Sport 2007, Руководство пользователя

Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы:

Похожие инструкции для MX-5 Miata Sport 2007

Бренды по названию

Популярные бренды