Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 1634 | Manualshive

Страница: 1634 / 2244

background image

Fig. 12: Identifying Discharge Headlight Bulb

Courtesy of MAZDA MOTORS CORP.

8. Install in the reverse order of removal.

HIGH-BEAM

1. Remove the battery cover.

2. Disconnect the negative battery cable. (See

BATTERY REMOVAL/INSTALLATION [LF]

.)

3. Disconnect the connector.

4. Remove the socket, then remove the headlight bulb.

5. Install in the reverse order of removal.

CAUTION:



A halogen bulb generates extremely high heat when it is
illuminated. If the surface of the bulb is soiled, excessive heat
will build up and the life of the bulb will be shortened. When
replacing the bulb, hold the metal flange, not the glass. Wipe off
any finger prints before installation.

2007 Mazda MX-5 Miata Sport

2007 ACCESSORIES & BODY, CAB Lighting Systems - MX-5 Miata

Microsoft

Thursday, July 09, 2009 3:27:42 PM

Page 13

© 2005 Mitchell Repair Information Company, LLC.

«
...
1632
1633
1634
1635
1636
...
»

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MX-5 Miata Sport 2007

Бренд: LAMBORGHINI Страницы: 48

Бренд: AccuAir Страницы: 40

Бренд: Peak Страницы: 10

Бренд: Mobile Create Страницы: 15

Бренд: Phonocar Страницы: 2

Quattroporte Automatic

Бренд: Maserati Страницы: 272

Vantage 12 Series

Бренд: Ecco Страницы: 5

Бренд: Waeco Страницы: 172

Бренд: VBG Страницы: 16

Бренд: Draw tite Страницы: 4

Бренд: EFILive Страницы: 25

Бренд: Saab Страницы: 92

Бренд: A-rival Страницы: 23

Бренд: Saturn Страницы: 440

Бренд: WABCO Страницы: 34

Бренд: Edelbrock Страницы: 2

Бренд: Mercedes-Benz Страницы: 93

Бренд: Gentex Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды