Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 1811

Страница: 1811 / 2244

POWER WINDOW SYSTEM PRELIMINARY INSPECTION[POWER WINDOW
SYSTEM]

MANUAL OPEN/CLOSE FUNCTION INSPECTION

MANUAL OPEN/CLOSE FUNCTION INSPECTION CHART

NO.1 THE AUTO OPEN FUNCTION ON THE DRIVER'S AND PASSENGER'S SIDE
POWER WINDOW IS INOPERATIVE[POWER WINDOW SYSTEM]

NO.2 THE DRIVER'S SIDE POWER WINDOW IS INOPERATIVE[POWER
WINDOW SYSTEM]

NO.3 THE PASSENGER'S SIDE POWER WINDOW IS INOPERATIVE[POWER
WINDOW SYSTEM]

NO.4 ALL POWER WINDOWS ARE INOPERATIVE[POWER WINDOW SYSTEM]

NO.5 ABNORMAL NOISE WHILE THE DOOR GLASS IS OPENIGN OR CLOSING
[POWER WINDOW SYSTEM]

STEP

INSPECTION

ACTION



Turn the ignition switch to the
ON position.



Operate the driver-side power
window using the manual
open/close function on the power
window main switch.



Does the driver-side power
window operate properly?

Yes

Go to the next step.



Inspect the following items:



Power window main switch
power supply fuse



Power window main switch
ground wiring harness



Power window main switch
power supply wiring harness



Wiring harness between
power window main switch
and driver-side power window
motor



Power window main switch
(driver-side power window
control is malfunctioning)



Driver-side power window
motor



Repair or replace the malfunctioning
part, then go to the next step.



Operate the passenger-side power
window using the power window
main switch.



Does the passenger-side power
window operate properly?

Yes



Manual open/close function is
normal.



Perform the auto open/close
function inspection.



Inspect the following items:



Wiring harness between

2007 Mazda MX-5 Miata Sport

2007 ACCESSORIES & BODY, CAB Symptom Troubleshooting (Power Window System) - MX-5 Miata

Microsoft

Thursday, July 09, 2009 3:25:15 PM

Page 6

«
...
1809
1810
1811
1812
1813
...
»

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы:

Похожие инструкции для MX-5 Miata Sport 2007

Бренды по названию

Популярные бренды

Mazda MX-5 Miata Sport 2007, Руководство пользователя

Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы:

Похожие инструкции для MX-5 Miata Sport 2007

Бренды по названию

Популярные бренды