Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 423 | Manualshive

Страница: 423 / 2244

background image

Fig. 58: Identifying Retaining Plates, Drive And Driven Plates

65. Inspect the lining of all drive plates.



If the lining is flaking or has changed color, or if it is worn or the print mark is wearing away,
replace with a new drive plate. When replacing, inspect the contact surfaces between the retaining
plate, driven plate and drive plate. If they are scratched or have changed color, replace with new
parts.

66. Remove the middle planetary gear component and sun gear.

67. Remove the bearing race and thrust needle bearing from middle planetary gear component.

NOTE:



Before replacing with new drive plates, soak them at least 2 h in
ATF.

Fig. 59: Identifying Print Mark Location

2007 Mazda MX-5 Miata Sport

2006-08 TRANSMISSION Automatic Transmission Overhaul - MX-5 Miata & RX-8

Microsoft

Thursday, July 09, 2009 1:42:24 PM

Page 27

© 2005 Mitchell Repair Information Company, LLC.

«
...
421
422
423
424
425
...
»

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MX-5 Miata Sport 2007

Бренд: A-Tach Mounts Страницы: 2

Бренд: A-Tach Mounts Страницы: 2

Бренд: A-Tach Mounts Страницы: 2

Бренд: Jeep Страницы: 322

Бренд: Jeep Страницы: 341

Бренд: Jeep Страницы: 310

Бренд: Jeep Страницы: 189

Бренд: Jeep Страницы: 26

Бренд: Jeep Страницы: 21

NPL-TV 7874 DIGITAL

Бренд: Napoli Страницы: 20

Бренд: BGS technic Страницы: 5

Бренд: Oldsmobile Страницы: 344

Бренд: ABL Страницы: 66

Бренд: Saab Страницы: 3

Бренд: Jeep Страницы: 16

Бренд: Audi Страницы: 4

Jumpy Miltispace

Бренд: CITROËN Страницы: 164

Бренд: Directed Страницы: 30

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды