manualshive.com logo in svg

Mazda MX-5 Miata Sport 2007, Руководство пользователя, Страница: 794 / 2244

Поделиться
Скачать
Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 794

Fig. 48: Inspecting Tooth Contact Pattern In Locations Around Ring Gear

 

Courtesy of MAZDA MOTORS CORP.

 

4. If the toe and flank contact points appear as shown in 

Fig. 49

 after the drive pinion and ring gear teeth 

contact inspection, replace the spacer with a thinner one, and move the drive pinion outward. 

 

2007 Mazda MX-5 Miata Sport 

2007 DRIVELINE/AXLES Differential - MX-5 Miata

  

Microsoft 

 

Thursday, July 09, 2009 3:11:17 PM

Page 50 

© 2005 Mitchell Repair Information Company, LLC. 

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов