Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 1063 | Manualshive

Страница: 1063 / 2244

background image

KNOCK SENSOR (KS) REMOVAL/INSTALLATION [LF]

1. Remove the battery cover.

2. Remove the negative battery cable. (See

BATTERY REMOVAL/INSTALLATION [LF]

.)

3. Remove the dynamic chamber. (See

INTAKE-AIR SYSTEM REMOVAL/INSTALLATION [LF]

.)

4. Disconnect the KS connector.

Fig. 71: Identifying Knock Sensor

Courtesy of MAZDA MOTORS CORP.

5. Remove the KS installation bolt, then remove the KS.

6. Install in the reverse order of removal.

KS tightening torque

16-24 N.m {1.7-2.4 kgf.m, 12-17 ft.lbf}

KNOCK SENSOR (KS) INSPECTION [LF]

RESISTANCE INSPECTION

NOTE:



Before performing the following inspection, make sure to follow the
procedure as indicated in the troubleshooting flow diagram. (See
TROUBLESHOOTING PROCEDURE .)

2007 Mazda MX-5 Miata Sport

2007 ENGINE PERFORMANCE Engine Control System - MX-5 Miata

Microsoft

Thursday, July 09, 2009 2:41:11 PM

Page 98

© 2005 Mitchell Repair Information Company, LLC.

«
...
1061
1062
1063
1064
1065
...
»

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MX-5 Miata Sport 2007

Бренд: RAM Страницы: 292

Бренд: RAM Страницы: 116

Бренд: Yakima Страницы: 8

Бренд: Yakima Страницы: 12

Бренд: Tessera4x4 Страницы: 20

Бренд: EUFAB Страницы: 52

Бренд: Maserati Страницы: 210

Бренд: OnStar Страницы: 22

STEALTH POWER RBP-216-SP

Бренд: RBP Страницы: 16

STREET SUPER SHIFTER

Бренд: HURST Страницы: 2

Бренд: XTC Страницы: 4

Бренд: walser Страницы: 24

Бренд: UAZ Страницы: 90

Бренд: Kargo Master Страницы: 19

PRIME DESIGN VBR3-FT31B

Бренд: Safe Fleet Страницы: 12

Бренд: Thule Страницы: 4

Бренд: SAFARI Страницы: 5

Бренд: Blaupunkt Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды