Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 1345 | Manualshive

Страница: 1345 / 2244

background image

Fig. 4: Removing Fuel Pump Relay

Courtesy of MAZDA MOTORS CORP.

3. Start the engine.

4. After the engine stalls, crank the engine

several times

.

5. Turn the ignition switch to the LOCK position.

6. Install the fuel pump relay.

AFTER SERVICE PRECAUTION [LF]

FUEL LEAKAGE INSPECTION

Using M-MDS or Equivalent

WARNING:



Fuel is very flammable liquid. If fuel spills or leaks from the
pressurized fuel system, it will cause serious injury or death and
facility breakage. Fuel can also irritate skin and eyes. To prevent
this, always complete the

Fuel Leakage Inspection

.

WARNING:



Fuel is very flammable liquid. If fuel spills or leaks from the
pressurized fuel system, it will cause serious injury or death and
facility breakage. Fuel can also irritate skin and eyes. To prevent
this, complete the following inspection with the engine stopped.

2007 Mazda MX-5 Miata Sport

2007 ENGINE Fuel System - MX-5 Miata

Microsoft

Thursday, July 09, 2009 2:37:12 PM

Page 4

© 2005 Mitchell Repair Information Company, LLC.

«
...
1343
1344
1345
1346
1347
...
»

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MX-5 Miata Sport 2007

Бренд: Daihatsu Страницы: 485

Бренд: Jeep Страницы: 322

Бренд: Jeep Страницы: 341

Бренд: Jeep Страницы: 310

Бренд: Jeep Страницы: 189

Бренд: Jeep Страницы: 26

Бренд: Jeep Страницы: 21

Бренд: Jeep Страницы: 673

Бренд: Ford Страницы: 38

Lippert Components LEVELEGS MPD 66385

Бренд: Atwood Страницы: 6

65 41 2 152 528

Бренд: BMW Страницы: 21

BASIC TLL171231

Бренд: Tellur Страницы: 5

TX-STAMP-4-FC04

Бренд: Over Armour Offroad Страницы: 9

Бренд: Fabbri Страницы: 32

Бренд: Whelen Engineering Company Страницы: 2

Бренд: Meritor Страницы: 20

SB-J-GCHER2/10W3v2

Бренд: Stealthbox Страницы: 2

Бренд: Scosche Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды