Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 1819 | Manualshive

Страница: 1819 / 2244

background image

side power window using the
power window main switch.



Is the voltage B+?

Power retractable hardtop
model:



Open: terminal 1F/close:
terminal 1D

Soft-top model:



Open: terminal D/close:
terminal A

No

Replace the power window main switch.
(See

POWER WINDOW MAIN

SWITCH
REMOVAL/INSTALLATION

.)

3



Measure the voltage at the power
window motor (battery power
supply terminal) while operating
the passenger's side power
window using the power window
main switch.



Is the voltage B+?

(Open: terminal A/close: terminal
G)

Yes

Go to the next step.

No

Inspect for an open or short circuit in the
wiring harness between the power window
main switch and the power window motor.
Inspect the power window main switch and
power window motor connector
connections. (damage/pulled-out pins,
corrosion)
Repair or replace as necessary.

4



Operate the passenger's side
power window using the power
window main switch.



Does the power window motor
operate (rotate)?

CAUTION:



If the power window
motor temperature is
high, the motor may not
rotate due to the motor
internal bimetal function.
Leave it untouched for
about 3 min to cool it,
then reinspect.

Yes

Go to the next step.

No

Replace the power window motor.
(See

POWER WINDOW REGULATOR

REMOVAL/INSTALLATION

.)

5



Remove the door glass from
carrier plate.



Make sure that the door glass
moves smoothly using your hand.



Does the door glass move

Yes

Replace the power window regulator.
(See

POWER WINDOW REGULATOR

REMOVAL/INSTALLATION

.)

No

Inspect for a bent regulator guide or other
possible malfunction.
If normal, replace the door glass run-

2007 Mazda MX-5 Miata Sport

2007 ACCESSORIES & BODY, CAB Symptom Troubleshooting (Power Window System) - MX-5 Miata

Microsoft

Thursday, July 09, 2009 3:25:15 PM

Page 14

© 2005 Mitchell Repair Information Company, LLC.

«
...
1817
1818
1819
1820
1821
...
»

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MX-5 Miata Sport 2007

Cushman Turf Truckster

Бренд: Jacobsen Страницы: 210

Бренд: femkes Страницы: 7

Бренд: BURY Страницы: 2

Бренд: Harman Kardon Страницы: 16

Бренд: TATA Motors Страницы: 184

PW-50C Civilian

Бренд: B&G electronics Страницы: 7

Бренд: ULTIMATE SPEED Страницы: 6

Бренд: SIXTOL Страницы: 32

Tipper Remote Kit

Бренд: Nugent Страницы: 21

10.297.300K-303K

Бренд: AUTOTECH Страницы: 1

Бренд: SkyRack Страницы: 2

Бренд: Stack Страницы: 4

Бренд: Quadratec Страницы: 4

DynaSport Roof Rack

Бренд: Perrycraft Страницы: 4

Бренд: Toyota Страницы: 307

Бренд: Porsche Страницы: 347

PORTABLE TYRE PUMP

Бренд: Toyota Страницы: 7

Бренд: K-Mate Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды