Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 1996 | Manualshive

Страница: 1996 / 2244

background image

DIAGNOSTIC PROCEDURE

ENGINE STALLS/QUITS, ENGINE RUNS ROUGH, MISSES, BUCK/JERK,
HESITATION/STUMBLE, SURGES DIAGNOSTIC PROCEDURE TABLE

skin and eyes. To prevent this, always
complete "BEFORE SERVICE
PRECAUTION" and "AFTER SERVICE
PRECAUTION" described in this article.

(See BEFORE SERVICE PRECAUTION [LF] .)

(See AFTER SERVICE PRECAUTION [LF] .)

CAUTION:



Disconnecting/connecting quick release
connector without cleaning it may cause
damage to fuel pipe and quick release
connector. Always clean quick release
connector joint area before
disconnecting/connecting, and make sure
that it is free of foreign material.

STEP

INSPECTION

RESULTS

ACTION

1

Verify the following:



Vacuum
connection



Air cleaner
element



No air leakage
from intake-air
system



No restriction of
intake-air system



Proper sealing of
intake manifold
and components
attached to intake
manifold: such as
EGR valve



Ignition wiring



Fuel quality (such
as proper octane,
contamination,
winter/summer

Yes

Go to the next step.

No

Service if necessary.
Repeat Step 1.

2007 Mazda MX-5 Miata Sport

2007 ENGINE PERFORMANCE Symptom Troubleshooting - MX-5 Miata

Microsoft

Thursday, July 09, 2009 2:42:10 PM

Page 63

© 2005 Mitchell Repair Information Company, LLC.

«
...
1994
1995
1996
1997
1998
...
»

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MX-5 Miata Sport 2007

Бренд: IAME Страницы: 17

Бренд: Yakima Страницы: 12

Бренд: JEHNERT SOUND DESIGN Страницы: 8

Experience Series

Бренд: Rainbow Страницы: 19

Бренд: Yakima Страницы: 12

iBoard IB-ZK406

Бренд: APS Auto Parts Specialist Страницы: 3

Бренд: BGS technic Страницы: 5

Бренд: Oldsmobile Страницы: 344

Бренд: ABL Страницы: 66

Бренд: Audi Страницы: 9

Бренд: Belkin Страницы: 4

DAF CHARGEMAX 90

Бренд: Paccar Страницы: 40

Бренд: Veldo Teknoloji Страницы: 32

Бренд: Thule Страницы: 4

Fleetwood Brougham Sedan 1966

Бренд: Cadillac Страницы: 56

Бренд: Brink Страницы: 26

Бренд: Goobay Страницы: 2

Бренд: Mazda Страницы: 604

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды