Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 1511

Страница: 1511 / 2244

Check Code 57

CHECK CODE 57

Check Code 59

reminder
switch



Wiring
harness
(Key
reminder
switch-
instrument
cluster)

Input signal to the

instrument cluster is

normal.

Check code 57

Panel light control signal

INSPECTION

CONDITION

DISPLAY

ACTION

Turn the headlight

switch to the TNS

position.

After selecting

check code 57, wait

approx. 2 s.

Illumination light

(hazard warning

switch, center panel

module, etc.) flashes

three times.

The panel light control signal is
normal.

Except above

Verify that the voltage of

instrument cluster terminal 1F is

B+.



If the voltage is as

specified, replace the

instrument cluster.



If the voltage is not as

specified, inspect the

following parts:



Illumination light

(hazard warning

switch, center panel

module, etc.)



Wiring harness

(Instrument cluster-

illumination lights-

TNS relay)

2007 Mazda MX-5 Miata Sport

2007 ACCESSORIES & BODY, CAB Instrumentation-Driver Info - MX-5 Miata

Microsoft

Thursday, July 09, 2009 3:30:27 PM

Page 23

«
...
1509
1510
1511
1512
1513
...
»

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы:

Похожие инструкции для MX-5 Miata Sport 2007

Бренды по названию

Популярные бренды

Mazda MX-5 Miata Sport 2007, Руководство пользователя

Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы:

Похожие инструкции для MX-5 Miata Sport 2007

Бренды по названию

Популярные бренды