Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 2022 | Manualshive

Страница: 2022 / 2244

background image

(See

COOLING FAN

CONTROL SYSTEM
INSPECTION

.)

Does the cooling fan control
system function properly?

No

Repair or replace the
malfunctioning part.

6

Is the drive belt normal?

Yes

Go to the next step.

No

Replace the drive belt.

7

Is there leakage around the
heater unit in passenger
compartment?

Yes

Inspect and service
heater for leakage.

No

Go to the next step.

8

Is there leakage at the coolant
hoses and/or radiator?

Yes

Replace the
malfunctioning part.

No

Go to the next step.

9

Cool down the engine.
Remove thermostat and inspect
operation.
(See

THERMOSTAT

REMOVAL/INSTALLATION
[LF]

.)

(See

THERMOSTAT

INSPECTION [LF]

.)

Is thermostat normal?

Yes

The engine coolant
temperature and
thermostat are normal,
inspect engine block for
leakage or blockage.

No

Access ECT PID.
Inspect for both ECT
PID and temperature
gauge readings.
If temperature gauge on
instrument cluster
indicates normal range
but ECT PID is not
same as temperature
gauge reading, inspect
ECT sensor.
If temperature gauge on
instrument cluster
indicates overheating
but ECT PID is normal,
inspect temperature
gauge and heat gauge
unit.

10



Verify test results.



If normal, return to diagnostic index to service any additional
symptoms.

(See

ENGINE SYMPTOM TROUBLESHOOTING [LF]

.)



If malfunction remains, inspect related Service Bulletins and/or On-
line Repair Information and perform repair or diagnosis.



If vehicle is repaired, troubleshooting completed.

2007 Mazda MX-5 Miata Sport

2007 ENGINE PERFORMANCE Symptom Troubleshooting - MX-5 Miata

Microsoft

Thursday, July 09, 2009 2:42:10 PM

Page 89

© 2005 Mitchell Repair Information Company, LLC.

«
...
2020
2021
2022
2023
2024
...
»

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MX-5 Miata Sport 2007

Бренд: FORM FIT Страницы: 2

WrapAround Windjammer

Бренд: Bestop Страницы: 7

signal mirror 2005-2009 Ford Mustang

Бренд: muth Страницы: 9

Бренд: Condor Страницы: 2

Parrot MKi + ParrotCK3100 range LOGAN

Бренд: Parrot Страницы: 10

Бренд: Toyota Страницы: 600

Бренд: Mazda Страницы: 3

Бренд: Pontiac Страницы: 20

Бренд: BMW Страницы: 392

Бренд: Curt Manufacturing Страницы: 4

Бренд: Horn Tools Страницы: 12

Бренд: Rugged Ridge Страницы: 5

Бренд: Lexus Страницы: 82

Бренд: Toyota Страницы: 36

Бренд: Menabo Страницы: 8

Бренд: Kargo Master Страницы: 17

Бренд: Erich Jaeger Страницы: 16

Бренд: HAKR Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды