manualshive.com logo in svg

Mazda MX-5 Miata Sport 2007, Руководство пользователя, Страница: 29 / 2244

Поделиться
Скачать
Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 29

Fig. 29: Removing Valve Guide From Combustion Chamber Side

 

Courtesy of MAZDA MOTORS CORP.

 

Valve Guide Installation 

1. Assemble the 

SSTs

 so that depth L is as specified. 

Valve guide protrusion height (standard)

  

12.2-12.8 mm {0.481-0.503 in}

  

 

2007 Mazda MX-5 Miata Sport 

2006-08 ENGINE Mechanical - Overhaul - 2.0L (LF) & 2.3L (L3) - Mazda6 & MX-5 Miata

  

Microsoft 

 

Thursday, July 09, 2009 2:43:25 PM

Page 29 

© 2005 Mitchell Repair Information Company, LLC. 

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов