Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 2020 | Manualshive

Страница: 2020 / 2244

background image

DIAGNOSTIC PROCEDURE

COOLING SYSTEM CONCERNS-OVERHEATING DIAGNOSTIC PROCEDURE TABLE

POSSIBLE CAUSE



A/C system operation is improper



Improper water/anti-freeze mixture



Fans reverse rotation



Poor radiator condition



Thermostat malfunction



Radiator hoses damage



Improper or damaged radiator cap



Cooling fan is inoperative.



Coolant overflow system malfunction



Improper tension of drive belt



Drive belt damage

STEP

INSPECTION

RESULTS

ACTION

1

Inspect the following:



Engine coolant level



Coolant leakage



Water and anti-freeze
mixture



Radiator condition



Collapsed or restricted
radiator hoses



Radiator pressure cap



Overflow system



Fan rotational direction



Fuses

Are all items normal?

Yes

Go to the next step.

No

Service if necessary.
Repeat Step 1.

2

Connect the M-MDS or
equivalent to the DLC-2.
Turn the ignition switch to the
ON position (Engine off).
Retrieve any DTCs.
Are there any DTCs displayed?

Yes

DTC is displayed:

Go to the appropriate
DTC inspection.
(See

DTC TABLE

[LF]

.)

No

No DTC is displayed:

Go to the next step.

3

Start the engine and idle it.
Turn the A/C switch on and set

Yes

Go to Step 5.

No

Inspect for the

2007 Mazda MX-5 Miata Sport

2007 ENGINE PERFORMANCE Symptom Troubleshooting - MX-5 Miata

Microsoft

Thursday, July 09, 2009 2:42:10 PM

Page 87

© 2005 Mitchell Repair Information Company, LLC.

«
...
2018
2019
2020
2021
2022
...
»

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MX-5 Miata Sport 2007

Бренд: Kargo Master Страницы: 5

Бренд: PAC Страницы: 15

Бренд: 3SIXT Страницы: 12

Бренд: Metra Electronics Страницы: 12

Бренд: Halfords Страницы: 4

Бренд: Velleman Страницы: 6

Бренд: Honda Страницы: 208

Бренд: Whispbar Страницы: 15

Бренд: Hyundai Страницы: 11

Бренд: Yakima Страницы: 13

Бренд: v.link Страницы: 21

Бренд: S3 Power Sports Страницы: 2

2004 Impreza OUTBACK SPORT

Бренд: Subaru Страницы: 34

Бренд: Maserati Страницы: 302

Бренд: Fiat Страницы: 284

TOUR EASY 4 936550

Бренд: Reimo Страницы: 4

C-Max Energi 2014

Бренд: Ford Страницы: 10

Бренд: Magneti Marelli Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды