Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 2244

background image

Fig. 19: Exploded View Of Cylinder Block (II) Disassembly

Courtesy of MAZDA MOTORS CORP.

Connecting Rod Cap Disassembly Note

1. Before removing connecting rod inspect the connecting rod side clearance. (See

CONNECTING ROD

INSPECTION

).

2. Remove the connecting rod bolt from the connecting rod cap by tapping the bolt with a plastic hammer.

Main Bearing Cap Disassembly Note

1. Before removing main bearing cap inspect the crankshaft end play. (See

CRANKSHAFT

NOTE:



The tappets are numbered to make sure they are assembled in their
original positions. When removed, keep the tappets with the cylinder
head they were removed from. Do not mix the tappets.

2007 Mazda MX-5 Miata Sport

2006-08 ENGINE Mechanical - Overhaul - 2.0L (LF) & 2.3L (L3) - Mazda6 & MX-5 Miata

Microsoft

Thursday, July 09, 2009 2:43:25 PM

Page 20

© 2005 Mitchell Repair Information Company, LLC.

«
...
18
19
20
21
22
...
»

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MX-5 Miata Sport 2007

Бренд: Kargo Master Страницы: 6

Бренд: Fabbri Страницы: 4

2005 Sierra Denali

Бренд: GMC Страницы: 428

Бренд: Mercedes-Benz Страницы: 346

Бренд: Thule Страницы: 4

STRONGARM RVR303

Бренд: Blue Giant Страницы: 48

Бренд: Harman Kardon Страницы: 16

Бренд: TATA Motors Страницы: 184

PW-50C Civilian

Бренд: B&G electronics Страницы: 7

Бренд: Hyundai Страницы: 19

Бренд: Cadillac Страницы: 2

Бренд: Buick Страницы: 20

Бренд: Edelbrock Страницы: 2

Бренд: Mercedes-Benz Страницы: 93

Бренд: TATA Motors Страницы: 308

Бренд: Lund Страницы: 12

Бренд: Acura Страницы: 4

Бренд: Kia Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды