Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 1579

Страница: 1579 / 2244

6. Remove the B-pillar upper trim.

Fig. 40: Removing B-Pillar Upper Trim

Courtesy of MAZDA MOTORS CORP.

B-PILLAR UPPER TRIM INSTALLATION [DETACHABLE HARDTOP]

1. When installing a new B-pillar upper trim, follow the procedure below:

1. Remove the adhesive remaining on the body using razor.

2. Remove any grease or dirt from the adhesion surface of the body.

2. When reusing the B-pillar upper trim, follow the procedure below:

1. Remove the adhesive remaining on the B-pillar upper trim and the body using a razor.

2. Remove any grease or dirt from the adhesion surface of the B-pillar upper trim and the body.

3. Apply primer to the bonding area of the B-pillar upper trim.

gloves when using a razor.

NOTE:



Double-sided adhesive tape has already been attached to the new rear
door garnish.

WARNING:



Using a razor with bare hands can cause injury. Always wear gloves
when using a razor.

2007 Mazda MX-5 Miata Sport

2007 ACCESSORIES & BODY, CAB Interior Trim - MX-5 Miata

Microsoft

Thursday, July 09, 2009 3:29:26 PM

Page 38

«
...
1577
1578
1579
1580
1581
...
»

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы:

Похожие инструкции для MX-5 Miata Sport 2007

Бренды по названию

Популярные бренды

Mazda MX-5 Miata Sport 2007, Руководство пользователя

Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы:

Похожие инструкции для MX-5 Miata Sport 2007

Бренды по названию

Популярные бренды