Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 1024 | Manualshive

Страница: 1024 / 2244

background image

Fig. 34: Identifying MAF/IAT Sensor

Courtesy of MAZDA MOTORS CORP.

5. Install in the reverse order of removal.

MAF/IAT sensor tightening torque

0.55-0.82 N.m {5.7-8.3 kgf.cm, 4.9-7.2 in.lbf}

MASS AIR FLOW (MAF) SENSOR INSPECTION [LF]

VISUAL INSPECTION

1. Visually inspect the MAF sensor for the following:



Damage, cracks



Rusted sensor terminal



Bent sensor terminal



If there is any malfunction, replace the MAF/IAT sensor. (See

MASS AIR FLOW

(MAF)/INTAKE AIR TEMPERATURE (IAT) SENSOR

NOTE:



Before performing the following inspection, make sure to follow the
procedure as indicated in the troubleshooting flow diagram. (See
TROUBLESHOOTING PROCEDURE .)

2007 Mazda MX-5 Miata Sport

2007 ENGINE PERFORMANCE Engine Control System - MX-5 Miata

Microsoft

Thursday, July 09, 2009 2:41:10 PM

Page 59

© 2005 Mitchell Repair Information Company, LLC.

«
...
1022
1023
1024
1025
1026
...
»

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MX-5 Miata Sport 2007

UNIVERSAL CJ-2A

Бренд: Jeep Страницы: 27

Бренд: Jeep Страницы: 228

Бренд: Jeep Страницы: 108

Бренд: Jeep Страницы: 525

Бренд: FABBRI PORTATUTTO Страницы: 2

Бренд: Mitsubishi Страницы: 160

Бренд: Cadillac Страницы: 442

DLD Wide Range II

Бренд: VDO Страницы: 84

TravelCharge Companion GO-Plus

Бренд: Wagan Страницы: 3

Бренд: Ford Страницы: 368

Бренд: ULTIMATE SPEED Страницы: 21

Бренд: Mini Страницы: 20

Бренд: Right Weigh Страницы: 16

inView 360 Fusion

Бренд: Safe Fleet Страницы: 27

ROADSIDE ASSISTANCE

Бренд: Seat Страницы: 44

Бренд: Hyundai Страницы: 19

Бренд: Simplicity Страницы: 10

1966 Spider 105

Бренд: Alfa Romeo Страницы: 46

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды