Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 137

Страница: 137 / 2244

DTC B2477 [ABS]

DTC B2477 POSSIBLE CAUSE TABLE

DIAGNOSTIC PROCEDURE

DTC B2477 DIAGNOSTIC PROCEDURE TABLE



Make sure to
reconnect all
disconnected
connectors.



Clear the DTC from
the memory.



(See

CLEARING

DTCS
PROCEDURES



Are the same DTCs
present?

Go to the next step.

VERIFY AFTER REPAIR
PROCEDURE



Are any other DTC
present?

Yes

Go to the applicable DTC inspection.
(See

DTC Table

DTC troubleshooting completed.

DTC B2477

ABS HU/CM configuration

DETECTION CONDITION



Configuration setting failure is detected.

POSSIBLE CAUSE



Module configuration procedure was not
completed properly.

STEP

INSPECTION

ACTION

VERIFY
CONFIGURATION



Has the ABS HU/CM
configuration been
performed?

Yes

Go to the next step.

Perform configuration using the M-
MDS.
(See

ABS CONFIGURATION

VERIFY DTC
TROUBLESHOOTING
COMPLETED



Clear the DTC from
the memory.



(See

CLEARING

DTCS

Yes

Repeat the inspection from Step 1.
If the malfunction recurs, replace the
ABS HU/CM.
(See

ABS HU/CM

REMOVAL/INSTALLATION

2007 Mazda MX-5 Miata Sport

2007 BRAKES On-Board Diagnostic (ABS) - MX-5 Miata

Microsoft

Thursday, July 09, 2009 3:17:55 PM

Page 15

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы:

Похожие инструкции для MX-5 Miata Sport 2007

Бренды по названию

Популярные бренды

Mazda MX-5 Miata Sport 2007, Руководство пользователя

Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы:

Похожие инструкции для MX-5 Miata Sport 2007

Бренды по названию

Популярные бренды