Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 2089 | Manualshive

Страница: 2089 / 2244

background image

10. Adjust the door glass. (See

DOOR GLASS ADJUSTMENT

.)

Fig. 4: Lifting Door Glass Up With Torque Specifications

Courtesy of MAZDA MOTORS CORP.

DOOR GLASS ADJUSTMENT

1. Fully close the door glass.

2. Remove the door trim.(See

DOOR TRIM REMOVAL/INSTALLATION

.)

3. Remove the door unit.(See

DOOR UNIT REMOVAL/INSTALLATION

.)

4. Connect the power window regulator connector.

5. Loosen the glass stopper installation bolts.

6. Loosen the power window regulator and door glass tightening nuts.

7. Align the door glass with the rear edge of the front beltline molding.

Fig. 5: Identifying Glass Stopper, Power Window Regulator With Bolt And Nut

NOTE:



The standard position for the rear edge of the front beltline molding
is 1 mm from the rear edge of the door panel. If the standard position
for the rear edge of the front beltline molding has deviated, align the
rear edge of the door glass to the standard position for the rear edge
position of the front beltline molding.

2007 Mazda MX-5 Miata Sport

2007 ACCESSORIES & BODY, CAB Glass/Windows/Mirrors - MX-5 Miata

Microsoft

Thursday, July 09, 2009 3:24:31 PM

Page 4

© 2005 Mitchell Repair Information Company, LLC.

«
...
2087
2088
2089
2090
2091
...
»

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MX-5 Miata Sport 2007

Green Motion DC 22

Бренд: Eaton Страницы: 65

Бренд: Hama Страницы: 40

Бренд: Tessera4x4 Страницы: 20

Бренд: Hyundai Страницы: 280

Бренд: Ford Страницы: 8

Бренд: Intec Страницы: 16

2003 Silhouette

Бренд: Oldsmobile Страницы: 466

Бренд: Peiying Страницы: 32

Бренд: Ford Страницы: 256

Бренд: Westin Страницы: 3

SHERPA SADDLE BAG JL

Бренд: Overland Outfitters Страницы: 2

Бренд: Saab Страницы: 9

Бренд: Diono Страницы: 9

Бренд: FALCON RIDGE Страницы: 5

Бренд: LAS Страницы: 10

Бренд: Metra Electronics Страницы: 8

PRIUS PRIME 2018

Бренд: Toyota Страницы: 68

Бренд: Blueant Страницы: 137

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды