Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 540

Страница: 540 / 2244

Dimension A

15.27-15.92 mm {0.61-0.62 in}

44. Measure the thickness of all the driven plates and drive plate components (3), and driven plates (3) at the

both ends across the diameter using a vernier caliper, and calculate the average value.

Dimension B

12.52-12.92 mm {0.493-0.508 in}

Fig. 306: Identifying Dimension A, B And H

45. Calculate the pack clearance using the following formula.

Dimension A-Dimension B-Thickness H

46. If the pack clearance exceeds the maximum specification, select the retaining plate with a clearance that

is the maximum specification and install it.

Pack clearance

0.42-0.72 mm {0.017-0.028 in}

Retaining plate thickness H (mm {in})

RETAINING PLATE THICKNESS

NOTE:



There are four types of retaining plates for the pack clearance
adjustment. Select the one with the most suitable thickness.

2007 Mazda MX-5 Miata Sport

2006-08 TRANSMISSION Automatic Transmission Overhaul - MX-5 Miata & RX-8

Microsoft

Thursday, July 09, 2009 1:42:25 PM

Page 144

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы:

Похожие инструкции для MX-5 Miata Sport 2007

Бренды по названию

Популярные бренды

Mazda MX-5 Miata Sport 2007, Руководство пользователя

Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы:

Похожие инструкции для MX-5 Miata Sport 2007

Бренды по названию

Популярные бренды