Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 68 | Manualshive

Страница: 68 / 2244

background image

Fig. 67: Removing Exhaust Camshaft Sprocket

Courtesy of MAZDA MOTORS CORP.

9. Loosen the camshaft cap bolts in several passes in the order shown in the figure.

NOTE:



The cylinder head and the camshaft caps are numbered to make sure
they are reassembled in their original position. When removed, keep
the caps with the cylinder head they were removed from. Do not mix
the caps.

2007 Mazda MX-5 Miata Sport

2006-08 ENGINE Mechanical - Overhaul - 2.0L (LF) & 2.3L (L3) - Mazda6 & MX-5 Miata

Microsoft

Thursday, July 09, 2009 2:43:25 PM

Page 68

© 2005 Mitchell Repair Information Company, LLC.

«
...
66
67
68
69
70
...
»

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MX-5 Miata Sport 2007

Бренд: TATA Motors Страницы: 94

Бренд: GÄN Страницы: 24

Бренд: Cadillac Страницы: 3

Бренд: Cadillac Страницы: 12

Бренд: Cadillac Страницы: 106

Бренд: Cadillac Страницы: 20

Бренд: Cadillac Страницы: 20

Бренд: Cadillac Страницы: 326

Бренд: Cadillac Страницы: 28

ESCALADE - BROCHURE 2009

Бренд: Cadillac Страницы: 602

ESCALADE ESV 2004

Бренд: Cadillac Страницы: 20

ESCALADE EXT 2005

Бренд: Cadillac Страницы: 460

CT6 SUPER CRUISE 2018

Бренд: Cadillac Страницы: 8

Бренд: Cadillac Страницы: 20

Бренд: Cadillac Страницы: 337

Бренд: Saab Страницы: 3

2008 MX-5 Miata

Бренд: Mazda Страницы: 400

Бренд: Phonocar Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды