Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 169

Страница: 169 / 2244

1. Remove the following parts:

1. Door trim (See

DOOR TRIM REMOVAL/INSTALLATION

2. Door glass (See

DOOR GLASS REMOVAL/INSTALLATION

3. Door speaker (See

DOOR SPEAKER REMOVAL/INSTALLATION

4. Door unit (See

DOOR UNIT REMOVAL/INSTALLATION

2. Detach the rod from the outer handle.

3. Remove the cover.

4. Remove the bolts.

Fig. 15: Identifying Outer Handle Bolts With Torque Specifications

Courtesy of MAZDA MOTORS CORP.

5. Secure the rear part of the front outer handle and, with the front outer handle lever pulled outward (1),

remove the rear part of the front outer handle from the front door.

6. Pull out the front part of the front outer handle from the front door.

7. Install in the reverse order of removal.

Fig. 16: Removing Rear Part Of Front Outer Handle From Front Door

Courtesy of MAZDA MOTORS CORP.

INNER HANDLE REMOVAL/INSTALLATION[ADVANCED KEYLESS
SYSTEM]

2007 Mazda MX-5 Miata Sport

2007 ACCESSORIES & BODY, CAB Security and Locks (Advanced Keyless System) - MX-5 Miata

Microsoft

Thursday, July 09, 2009 3:36:54 PM

Page 10

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы:

Похожие инструкции для MX-5 Miata Sport 2007

Бренды по названию

Популярные бренды

Mazda MX-5 Miata Sport 2007, Руководство пользователя

Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы:

Похожие инструкции для MX-5 Miata Sport 2007

Бренды по названию

Популярные бренды