Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 715

Страница: 715 / 2244

Fig. 29: Measuring Clutch Disc Maximum Runout Using Dial Gauge

Courtesy of MAZDA MOTORS CORP.

6. Install the clutch disc.

CLUTCH RELEASE COLLAR INSPECTION

1. Remove the clutch release collar.

2. Turn the collar while applying force in the axial direction, and inspect for sticking, excessive resistance,

and an abnormal noise.



If there is any malfunction, replace the clutch release collar.

CAUTION:



Do not clean the clutch release collar with cleaning fluids or a steam
cleaner because it is filled with grease.

2007 Mazda MX-5 Miata Sport

2007 TRANSMISSION Clutch - MX-5 Miata

Microsoft

Thursday, July 09, 2009 1:44:46 PM

Page 31

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы:

Похожие инструкции для MX-5 Miata Sport 2007

Бренды по названию

Популярные бренды

Mazda MX-5 Miata Sport 2007, Руководство пользователя

Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы:

Похожие инструкции для MX-5 Miata Sport 2007

Бренды по названию

Популярные бренды