Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 73

Страница: 73 / 2244

Fig. 72: Installing SST To Camshaft

Courtesy of MAZDA MOTORS CORP.

20. Hold the exhaust camshaft using a suitable wrench on the cast hexagon as shown in the figure.

21. Tighten the exhaust camshaft sprocket lock bolt.

Tightening torque

69-75 N.m {7.1-7.6 kgf.m, 50.9-55.3 ft.lbf}

22. Remove the

SST

from the camshaft.

23. Remove the

SST

from the block lower blind plug.

24. Rotate the crankshaft clockwise two turns until the TDC position.



If not aligned, loosen the camshaft sprocket lock bolt and repeat from Step 17.

2007 Mazda MX-5 Miata Sport

2006-08 ENGINE Mechanical - Overhaul - 2.0L (LF) & 2.3L (L3) - Mazda6 & MX-5 Miata

Microsoft

Thursday, July 09, 2009 2:43:26 PM

Page 73

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы:

Mazda MX-5 Miata Sport 2007, Руководство пользователя, Страница: 73 / 2244

Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы: