Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 232 | Manualshive

Страница: 232 / 2244

background image

Fig. 7: Air Bag Module & Pre-Tensioner Seat Belt Handling Caution

Courtesy of MAZDA MOTORS CORP.

SEAT WEIGHT SENSOR HANDLING



The seat weight sensor has a built-in strain gauge which may operate improperly if the sensor is
dropped by itself or when installed to the seat. If it is dropped, replace the seat weight sensor with a
new one.



Oil, grease, or water on the seat weight sensor may cause the system to operate (deploy)
improperly. Never allow oil, grease, or water to get on the seat weight sensor.



Foreign material in the seat weight sensor components may cause the system to operate (deploy)
improperly. Always make sure that no foreign material can get into the seat weight sensor.



Disassembling the seat weight sensor, or tightening any of the nuts and bolts installed to the sensor
body may cause it to operate (deploy) improperly. Never disassemble the seat weight sensor or
tighten any of the nuts or bolts installed to the body of the sensor.

AIR BAG MODULE, PRE-TENSIONER SEAT BELT REUSE



Even if an air bag module or a pre-tensioner seat belt does not operate (deploy) in a collision and
does not have any external signs of damage, it may have been damaged internally, which may cause
improper operation. Before reusing a live (undeployed) air bag module and the pre-tensioner seat
belts, always use the on-board diagnostic to diagnose the air bag module and the pre-tensioner seat
belts to verify that they have no malfunction.

AIR BAG WIRING HARNESS REPAIR

2008 Mazda MX-5 Miata Grand Touring

2008 RESTRAINTS Air Bag System - MX-5 Miata

Microsoft

Thursday, July 09, 2009 3:43:37 PM

Page 8

© 2005 Mitchell Repair Information Company, LLC.

«
...
230
231
232
233
234
...
»

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MX-5 Miata Sport 2007

Бренд: Daihatsu Страницы: 1718

Бренд: VEAP SHIELD UNITED Страницы: 3

Бренд: Harmar Mobility Страницы: 10

Бренд: iDataLink Страницы: 106

Cushman Turf Truckster

Бренд: Jacobsen Страницы: 210

Camaro 12000 1968 Series

Бренд: Chevrolet Страницы: 455

Бренд: BESAFE Страницы: 4

Бренд: Condor Страницы: 2

Бренд: Renault Страницы: 340

Бренд: Whelen Engineering Company Страницы: 9

Бренд: Mercedes-Benz Страницы: 358

Бренд: Subaru Страницы: 2

Бренд: Subaru Страницы: 328

Sedan CIVIC 2022

Бренд: Honda Страницы: 701

Бренд: NavInc Страницы: 6

Denali 1094-0185-15

Бренд: E&G Classics Страницы: 3

Бренд: Metra Electronics Страницы: 2

Бренд: Bestop Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды