manualshive.com logo in svg

Mazda MX-5 Miata Sport 2007, Руководство пользователя, Страница: 1924 / 2244

Поделиться
Скачать
Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 1924

between parts.  

The connector joints, points of vibration, and places where wire harnesses pass through the firewall, body 
panels and other panels are the major areas to be checked.  

Inspection Method for Switch and/or Sensor Connectors or Wires 

1. Connect M-MDS or equivalent to DLC-2.  

2. Turn the ignition switch to the ON position (engine off). 

3. Access PIDs for the switch you are inspecting.  

4. Turn switch on manually.  

5. Shake each connector or wire harness a bit vertically and horizontally while monitoring the PID. 

If PID value is unstable, check for poor connection.  

Fig. 3: Shaking Connector Or Wire Harness

 

Courtesy of MAZDA MOTORS CORP.

 

Inspection Method for Sensors 

1. Connect M-MDS or equivalent to DLC-2.  

2. Turn the ignition switch to the ON position (engine off). 

NOTE:

If engine starts and runs, perform the following steps at idle. 

 

2007 Mazda MX-5 Miata Sport 

2007 SUSPENSION Symptom Troubleshooting - MX-5 Miata

  

Microsoft 

 

Thursday, July 09, 2009 1:51:04 PM

Page 3 

© 2005 Mitchell Repair Information Company, LLC. 

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов