manualshive.com logo in svg

Mazda MX-5 Miata Sport 2007, Руководство пользователя, Страница: 1391 / 2244

Поделиться
Скачать
Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 1391

REMOVAL/INSTALLATION [LF]

.) 

5. Fix the fuel injector to the fuel distributor with a wire or the equivalent. 

Fig. 44: Fixing Fuel Injector To Fuel Distributor With Wire

 

Courtesy of MAZDA MOTORS CORP.

 

6. Connect the fuel hose.  

7. Start the fuel pump using the following procedure: 

Using M-MDS

  

1. Connect the negative battery cable.  

2. Connect the M-MDS to the DLC-2. 

 

2007 Mazda MX-5 Miata Sport 

2007 ENGINE Fuel System - MX-5 Miata

  

Microsoft 

 

Thursday, July 09, 2009 2:37:12 PM

Page 50 

© 2005 Mitchell Repair Information Company, LLC. 

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов