Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 2099

Страница: 2099 / 2244

Fig. 23: Power Window Main Switch Continuity Table

Courtesy of MAZDA MOTORS CORP.

POWER WINDOW MAIN SWITCH INSPECTION[POWER RETRACTABLE
HARDTOP]

WITH EXTERIOR OPEN FUNCTION

1. Measure the voltage at each terminal (other than terminals 1G, 1H, 2B and 2C).



If the voltage is not as specified in the Terminal Voltage Table, inspect the parts under "inspection
item(s)" and related wiring harnesses.

2. Disconnect the negative battery cable.

3. Inspect the power window main switch connector for continuity at terminal 1G.

4. If the system does not work properly even though the inspection items or related wiring harnesses do not

have any malfunction, replace the power window main switch.

POWER WINDOW MAIN SWITCH INSPECTION CHART (WITH EXTERIOR OPEN FUNCTION)

Terminal Signal name Connected to

Measured

condition

Voltage

(V)/Continuity

Inspection item (s)

Power supply

P/W 20 A

fuse

Under any
condition

B+



P/W 20 A fuse



Related wiring
harnesses

IG 1

IG KEY1 20

A fuse

Ignition switch is
at ON position

B+



Inspect IG KEY1 20 A
fuse



Related wiring
harnesses

Ignition switch is

at LOCK

position

1.0 or less

Close output

Power

While door glass
is opening

1.0 or less



Power window motor
(See

POWER

WINDOW MOTOR

2007 Mazda MX-5 Miata Sport

2007 ACCESSORIES & BODY, CAB Glass/Windows/Mirrors - MX-5 Miata

Microsoft

Thursday, July 09, 2009 3:24:31 PM

Page 14

«
...
2097
2098
2099
2100
2101
...
»

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы:

Похожие инструкции для MX-5 Miata Sport 2007

Бренды по названию

Популярные бренды

Mazda MX-5 Miata Sport 2007, Руководство пользователя

Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы:

Похожие инструкции для MX-5 Miata Sport 2007

Бренды по названию

Популярные бренды