Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 541

Страница: 541 / 2244

47. Install the drive plate, driven plates and retaining plate to the transmission component as shown in the

figure.

Fig. 307: Identifying Drive Plate, Driven Plates And Retaining Plate

48. Install the driven plates, drive plate, and the retaining plate in the order indicated in the figure.

49. Install the bearing race and thrust needle bearing to the middle planetary gear component.

Fig. 308: Identifying Driven Plates, Drive Plate And Retaining Plate

50. Install the middle planetary gear component and sun gear.

51. Apply ATF to the bearing race and thrust needle bearing.

52. Install the bearing race and thrust needle bearing to the middle planetary gear component.

Identification mark Thickness (mm {in})

1.95-2.05 {0.077-0.081}

2.15-2.25 {0.085-0.089}

2.35-2.45 {0.093-0.096}

2.55-2.65 {0.100-0.104}

CAUTION:



Inspect the number and order of the retaining plate, drive and
driven plates.

2007 Mazda MX-5 Miata Sport

2006-08 TRANSMISSION Automatic Transmission Overhaul - MX-5 Miata & RX-8

Microsoft

Thursday, July 09, 2009 1:42:25 PM

Page 145

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы:

Похожие инструкции для MX-5 Miata Sport 2007

Бренды по названию

Популярные бренды

Mazda MX-5 Miata Sport 2007, Руководство пользователя

Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы:

Похожие инструкции для MX-5 Miata Sport 2007

Бренды по названию

Популярные бренды