manualshive.com logo in svg

Mazda MX-5 Miata Sport 2007, Руководство пользователя, Страница: 1144 / 2244

Поделиться
Скачать
Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 1144

Leakage of engine oil, engine coolant, ATF, MT oil, and fuel  

Ignition timing, idle speed, and idle mixture (CO and HC) (See 

ENGINE TUNE-UP [LF]

 .)  

Front wheel alignment (See 

FRONT WHEEL ALIGNMENT

 .)  

Engine-driven accessories operation  

23. Perform the on-road test and verify that there is no vibration or noise.  

ENGINE, TRANSMISSION, CROSSMEMBER COMPONENT REMOVAL NOTE 

1. Secure the engine, transmission, and crossmember component using an engine lifter.  

ENGINE DISASSEMBLY/ASSEMBLY [LF] 

1. Remove the transmission from the engine. (See 

TRANSMISSION REMOVAL/INSTALLATION 

[M15M-D]

 .) (See 

TRANSMISSION REMOVAL/INSTALLATION [P66M-D]

 .) (See 

AUTOMATIC TRANSMISSION REMOVAL/INSTALLATION [SJ6A-EL]

 .)  

2. Remove the following parts: 

1. The clutch unit (MT) (See 

CLUTCH UNIT REMOVAL/INSTALLATION

 .)  

2. The ignition coil (See 

IGNITION COIL REMOVAL/INSTALLATION [LF]

 .)  

3. The CMP sensor (See 

CAMSHAFT POSITION (CMP) SENSOR 

REMOVAL/INSTALLATION [LF]

 .)  

4. The power steering oil pump (See 

POWER STEERING OIL PUMP 

REMOVAL/INSTALLATION

 .)  

5. The fuel distributor and fuel injector (See 

FUEL INJECTOR REMOVAL/INSTALLATION 

[LF]

 .)  

6. The intake-air system (See 

INTAKE-AIR SYSTEM REMOVAL/INSTALLATION [LF]

 .)  

7. The exhaust system (See 

EXHAUST SYSTEM REMOVAL/INSTALLATION [LF]

 .)  

8. The CKP sensor (See 

CRANKSHAFT POSITION (CKP) SENSOR 

REMOVAL/INSTALLATION [LF]

 .)  

3. Remove in the order indicated in 

Fig. 70

 .  

4. Install in the reverse order of removal. 

 

2007 Mazda MX-5 Miata Sport 

2007 ENGINE Mechanical - MX-5

  

Microsoft 

 

Thursday, July 09, 2009 3:21:51 PM

Page 78 

© 2005 Mitchell Repair Information Company, LLC. 

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов