Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 1581

Страница: 1581 / 2244

Fig. 42: Removing Tire House Trim

Courtesy of MAZDA MOTORS CORP.

6. Install in the reverse order of removal.

REAR PACKAGE TRIM REMOVAL/INSTALLATION

1. Remove the following parts:

1. Console (See

CONSOLE REMOVAL/INSTALLATION

2. Quarter trim (See

QUARTER TRIM REMOVAL/INSTALLATION

3. Scuff plate (See

SCUFF PLATE REMOVAL/INSTALLATION

4. Tire house trim (See

TIRE HOUSE TRIM REMOVAL/INSTALLATION

5. Aeroboard (See

AEROBOARD REMOVAL/INSTALLATION

6. Front seat back bar garnish (See

SEAT BACK BAR GARNISH

REMOVAL/INSTALLATION

7. Back trim (See

BACK TRIM REMOVAL/INSTALLATION

8. Seat belt set plate (See

SEAT BELT REMOVAL/INSTALLATION

9. Seat back crossmember assembly (See

SEAT BACK CROSSMEMBER ASSEMBLY

REMOVAL/INSTALLATION

10. Rear side trim (See

REAR SIDE TRIM REMOVAL/INSTALLATION

2. Remove the fasteners.

3. Remove the pins A and B.

2007 Mazda MX-5 Miata Sport

2007 ACCESSORIES & BODY, CAB Interior Trim - MX-5 Miata

Microsoft

Thursday, July 09, 2009 3:29:26 PM

Page 40

«
...
1579
1580
1581
1582
1583
...
»

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы:

Похожие инструкции для MX-5 Miata Sport 2007

Бренды по названию

Популярные бренды

Mazda MX-5 Miata Sport 2007, Руководство пользователя

Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы:

Похожие инструкции для MX-5 Miata Sport 2007

Бренды по названию

Популярные бренды