Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 1937 | Manualshive

Страница: 1937 / 2244

background image

Courtesy of MAZDA MOTORS CORP.

FOREWORD [LF]



When the customer reports a vehicle malfunction, check the malfunction indicator lamp (MIL) indication
and diagnostic trouble code (DTC), then diagnose the malfunction according to

Fig. 3

:



If a DTC exists, diagnose the applicable DTC inspection. (See

DTC TABLE [LF]

.)



If no DTC exists and the MIL does not illuminate or flash, diagnose the applicable symptom
troubleshooting. (See

QUICK DIAGNOSTIC TABLE [LF]

.)

Fig. 3: Malfunction Flow Diagram

Courtesy of MAZDA MOTORS CORP.

ENGINE SYMPTOM TROUBLESHOOTING [LF]



Confirm trouble symptom using the following diagnostic index, then go to appropriate troubleshooting
table.

DIAGNOSTIC INDEX

DIAGNOSTIC INDEX

No.

TROUBLESHOOTING ITEM

DESCRIPTION

REFERENC

1 Melting of main or other

fuses

-

(See

NO.1 MELTING

MAIN OR OTHER F
[LF]

.)

2007 Mazda MX-5 Miata Sport

2007 ENGINE PERFORMANCE Symptom Troubleshooting - MX-5 Miata

Microsoft

Thursday, July 09, 2009 2:42:09 PM

Page 4

© 2005 Mitchell Repair Information Company, LLC.

«
...
1935
1936
1937
1938
1939
...
»

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MX-5 Miata Sport 2007

Бренд: Feniex Страницы: 6

RadioPRO 5 RP5-GM41

Бренд: PAC Страницы: 3

Бренд: Rola Страницы: 3

1995 Cutlass Supreme

Бренд: Oldsmobile Страницы: 340

Бренд: Toyota Страницы: 497

Бренд: Jaeger Страницы: 11

Бренд: ATS Страницы: 12

TOUR EASY 4 936550

Бренд: Reimo Страницы: 4

Бренд: Ford Страницы: 264

Бренд: Metra Electronics Страницы: 16

Бренд: ULTIMATE SPEED Страницы: 132

Бренд: Lincoln Страницы: 370

Бренд: Chevrolet Страницы: 376

Civic Coupe 2009

Бренд: Honda Страницы: 414

Бренд: ZeroRPM Страницы: 41

Бренд: Whispbar Страницы: 42

Бренд: Vauxhall Страницы: 215

SILVER line 104

Бренд: AutoMaxi Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды