Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 1891 | Manualshive

Страница: 1891 / 2244

background image

Fig. 5: Removing Seat Bolts (With Torque Specifications)

Courtesy of MAZDA MOTORS CORP.

SEAT DISASSEMBLY/ASSEMBLY

WARNING:



Handling the seat (side air bag, seat weight sensor) improperly can
accidentally deploy the side air bag, which may seriously injure you.
Read the service warnings and cautions before handling the seat.
(See AIR BAG SYSTEM SERVICE WARNINGS .) (See AIR BAG
SYSTEM SERVICE CAUTIONS .)

CAUTION:



If any of the following work is performed, perform the seat weight
sensor calibration using the WDS or equivalent. (See SEAT WEIGHT
SENSOR CALIBRATION .)



Replacement with a new seat weight sensor



Replacement with a new seat weight sensor control module

2007 Mazda MX-5 Miata Sport

2007 ACCESSORIES & BODY, CAB Seats - MX-5 Miata

Microsoft

Thursday, July 09, 2009 3:26:44 PM

Page 5

© 2005 Mitchell Repair Information Company, LLC.

«
...
1889
1890
1891
1892
1893
...
»

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MX-5 Miata Sport 2007

Бренд: Ecco Страницы: 9

Бренд: Ecco Страницы: 9

Бренд: TATA Motors Страницы: 164

Бренд: Fabbri Страницы: 4

Бренд: Whispbar Страницы: 15

Automotive 31006

Бренд: KRAFTWERK Страницы: 2

Бренд: Menabo Страницы: 12

Бренд: Westin Страницы: 3

Бренд: Black Horse Off Road Страницы: 7

Бренд: Buick Страницы: 161

Бренд: Arrista Страницы: 2

Бренд: Acura Страницы: 19

Бренд: Ford Страницы: 325

Бренд: Lock'er Down Страницы: 2

Бренд: QA1 Страницы: 4

Бренд: Blue Bird Страницы: 111

Бренд: FEATHERLITE TRAILERS Страницы: 60

Бренд: DiscountRamps Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды