manualshive.com logo in svg

Mazda MX-5 Miata Sport 2007, Руководство пользователя, Страница: 1636 / 2244

Поделиться
Скачать
Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 1636

Fig. 14: Identifying Discharge Headlight Control Module

 

Courtesy of MAZDA MOTORS CORP.

 

DISCHARGE HEADLIGHT SYSTEM INSPECTION 

DISCHARGE HEADLIGHT INOPERATIVE 

WARNING:

Incorrect servicing of the discharge headlights could result in 
electrical shock. Before servicing the discharge headlights, always 
refer to the discharge headlight service warnings. (See DISCHARGE 
HEADLIGHT SERVICE WARNINGS .)  

 

2007 Mazda MX-5 Miata Sport 

2007 ACCESSORIES & BODY, CAB Lighting Systems - MX-5 Miata

  

Microsoft 

 

Thursday, July 09, 2009 3:27:42 PM

Page 15 

© 2005 Mitchell Repair Information Company, LLC. 

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов