Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 1099

Страница: 1099 / 2244

1. Remove the battery and battery tray. (See

BATTERY REMOVAL/INSTALLATION [LF]

2. Remove the air cleaner. (See

INTAKE-AIR SYSTEM REMOVAL/INSTALLATION [LF]

3. Disconnect the ventilation hose. (See

QUICK RELEASE CONNECTOR (EMISSION SYSTEM)

REMOVAL/INSTALLATION [LF]

4. Loosen the water pump pulley bolt and removal the drive belt. (See

DRIVE BELT REPLACEMENT

[LF]

5. Remove the front suspension tower bar (joint). (See

FRONT SUSPENSION TOWER BAR

REMOVAL/INSTALLATION

6. Remove the CMP sensor. (See

CAMSHAFT POSITION (CMP) SENSOR

REMOVAL/INSTALLATION [LF]

7. Disconnect the OCV connector.

8. Remove the ignition coils. (See

IGNITION COIL REMOVAL/INSTALLATION [LF]

9. Remove the drive belt. (See

DRIVE BELT REPLACEMENT [LF]

10. Remove the under cover. (See

TRANSVERSE MEMBER REMOVAL/INSTALLATION

11. Remove the CKP sensor. (See

CRANKSHAFT POSITION (CKP) SENSOR

REMOVAL/INSTALLATION [LF]

12. Remove the P/S oil pump with the oil hose still connected and position the P/S oil pump so that it is out

of the way. (See

POWER STEERING OIL PUMP REMOVAL/INSTALLATION

13. Move the cooler pipe No.3 and heater pipe slightly out of the way.

Fig. 29: Moving Cooler Pipe No. 3 & Heater Pipe

2007 Mazda MX-5 Miata Sport

2007 ENGINE Mechanical - MX-5

Microsoft

Thursday, July 09, 2009 3:21:51 PM

Page 33

«
...
1097
1098
1099
1100
1101
...
»

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы:

Похожие инструкции для MX-5 Miata Sport 2007

Бренды по названию

Популярные бренды

Mazda MX-5 Miata Sport 2007, Руководство пользователя

Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы:

Похожие инструкции для MX-5 Miata Sport 2007

Бренды по названию

Популярные бренды