Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 338 | Manualshive

Страница: 338 / 2244

background image



If the vehicle is to be scrapped, or when disposing of any air bag modules or pre-tensioner seat belts,
operate (deploy) them inside the vehicle by following the deployment procedure below and using the

SST

(Deployment tool).



When disposing of an operated (deployed) air bag module and pre-tensioner seat belt, refer to

AIR BAG

MODULE AND PRE-TENSIONER SEAT BELT DISPOSAL PROCEDURES

.

DEPLOYMENT PROCEDURE FOR INSIDE OF VEHICLE

1. Inspect the

SST

(Deployment tool). (See

INSPECTION OF SST (DEPLOYMENT TOOL)

.)

2. Move the vehicle to an open space, away from strong winds, and close all of the vehicle doors and

windows.

3. Turn the ignition switch to the LOCK position.

4. Remove the battery cover.

5. Disconnect the negative battery cable and wait for

1 min or more

. (See

BATTERY

REMOVAL/INSTALLATION [LF]

.)

6. Follow the procedure below for operating (deploying) the applicable air bag module or pre-tensioner seat

belt.

DRIVER-SIDE AIR BAG MODULE

1. Remove the driver-side air bag module. (See

DRIVER-SIDE AIR BAG MODULE

REMOVAL/INSTALLATION

.)

2. Connect the

SSTs

(Adapter harness) to the driver-side air bag module as shown in

Fig. 36

.

3. Install the driver-side air bag module. (See

DRIVER-SIDE AIR BAG MODULE

REMOVAL/INSTALLATION

.)

CAUTION:



Deploying the air bag modules and pre-tensioner seat belts inside
the vehicle may cause damage to the vehicle interior. When the
vehicle is not to be scrapped, always deploy the air bag modules and
pre-tensioner seat belts outside the vehicle.

WARNING:



The driver-side air bag module is a dual inflator type. If one inflator
is forced to operate (deploy), the other may operate (deploy)
accidentally. To prevent injury while disposing of the air bag
module, make sure to operate (deploy) both driver-side air bag
module inflators simultaneously, following the procedure below.

NOTE:



The SSTs , two types of adapter harnesses (for inflators No.1 and No.2)
and two deployment tools are to be used to operate (deploy) the driver-
side air bag module.

2007 Mazda MX-5 Miata Sport

2007 RESTRAINTS Air Bag System - MX-5 Miata

Microsoft

Thursday, July 09, 2009 2:12:55 PM

Page 38

© 2005 Mitchell Repair Information Company, LLC.

«
...
336
337
338
339
340
...
»

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MX-5 Miata Sport 2007

Бренд: Curt Manufacturing Страницы: 6

Бренд: Yakima Страницы: 13

Бренд: Menabo Страницы: 11

Polaris TATOU 4S

Бренд: Camoplast Страницы: 13

Бренд: Opel Страницы: 32

Бренд: Streetwize Страницы: 4

Бренд: Thule Страницы: 8

Бренд: Prorack Страницы: 14

Бренд: Tactik Страницы: 4

Бренд: banks Страницы: 76

Бренд: AA Products Страницы: 8

Бренд: Maxon Страницы: 10

Бренд: Webasto Страницы: 28

Бренд: Edelbrock Страницы: 2

1967 Calais Coupe

Бренд: Cadillac Страницы: 255

Бренд: Ford Страницы: 10

Бренд: Fiat Страницы: 204

Бренд: Chevrolet Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды