Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 227 | Manualshive

Страница: 227 / 2244

background image

Fig. 3: Air Bag Module Handling (1 Of 2)

Courtesy of MAZDA MOTORS CORP.



A live (undeployed) air bag module placed with its deployment surface to ground is dangerous. If
the air bag module were to accidentally operate (deploy), it could cause serious injury. Always
place a live (undeployed) air bag module with its deployment surface up.

2008 Mazda MX-5 Miata Grand Touring

2008 RESTRAINTS Air Bag System - MX-5 Miata

Microsoft

Thursday, July 09, 2009 3:43:36 PM

Page 3

© 2005 Mitchell Repair Information Company, LLC.

«
...
225
226
227
228
229
...
»

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MX-5 Miata Sport 2007

Бренд: UMBRA RIMORCHI Страницы: 18

Бренд: Warrior Products Страницы: 3

Бренд: Camcar Страницы: 6

Бренд: ABL Страницы: 4

Бренд: Honda Страницы: 32

Бренд: Raytel LLC Страницы: 40

Бренд: Chevrolet Страницы: 376

Бренд: Mazda Страницы: 15

Бренд: B-Speech Страницы: 4

Бренд: Vauxhall Страницы: 131

Бренд: Metra Electronics Страницы: 5

Бренд: Renkforce Страницы: 4

Бренд: SilverLeaf Electronics Страницы: 16

SANICON TURBO 300

Бренд: Thetford Страницы: 25

Бренд: ULTIMATE SPEED Страницы: 34

Бренд: Honda Страницы: 569

Бренд: FORM FIT Страницы: 2

Security Cage Kit

Бренд: Toro Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды