Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 1409

Страница: 1409 / 2244

Fig. 9: Assembling Evaporator Temperature Sensor

Courtesy of MAZDA MOTORS CORP.

EVAPORATOR INSPECTION

1. Inspect the evaporator for damage, cracks and oil leakage.



If there is any malfunction, replace the evaporator.

2. Visually inspect the fins for bending.



If there is any bending, use the end of a flathead screwdriver to straighten the fins.

HEATER CORE INSPECTION

1. Inspect the heater core for damage, cracks and water leakage.



If there is any malfunction, replace the heater core.

2. Visually inspect the fins for bending.



If there is any bending, use the end of a flathead screwdriver to straighten the fins.

3. Visually inspect the heater hose for deformation.



Repair with pliers if there is deformation. If there is any malfunction, replace the heater core.

2007 Mazda MX-5 Miata Sport

2007 HVAC Basic System - MX-5 Miata

Microsoft

Thursday, July 09, 2009 2:22:45 PM

Page 10

«
...
1407
1408
1409
1410
1411
...
»

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы:

Похожие инструкции для MX-5 Miata Sport 2007

Бренды по названию

Популярные бренды

Mazda MX-5 Miata Sport 2007, Руководство пользователя

Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы:

Похожие инструкции для MX-5 Miata Sport 2007

Бренды по названию

Популярные бренды