Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 199

Страница: 199 / 2244

(Door switch off)

harnesses

Unlock signal
input

Door lock-
link switch
(passenger-
side)

Passenger-side door
is unlocked: Inspect
for continuity to
ground.

Continuity detected

Door lock-link
switch (passenger-
side)

Passenger-side door
is locked: Inspect for
continuity to ground.

No continuity

(2)

Serial
communication

Power
window main
switch

Because this
terminal is for
communication,
good/no good
judgment by
terminal voltage is
not possible.



Power
window main
switch



Related
wiring
harnesses

Door switch
signal (LH)
output

Door switch

Door open(LH)
(Door switch on)

1.0 or less



Door switch
(LH)



Related
wiring
harnesses

Door closed (LH)
(Door switch off)

B+

Horn on/off

Horn relay

Other

B+



Horn relay



Related
wiring
harnesses

Transmitter LOCK
button is pressed
twice within 5 s.

Brarr;1.0or
lessrarr;B+

Hood switch
signal

Hood switch

Hood open (Hood
latch switch off)

B+



Hood latch
switch



Related
wiring
harnesses

Hood closed
(Hood latch switch
on)

1.0 or less

Keyless buzzer
output

Keyless
buzzer

Keyless buzzer
operated

B+

Keyless buzzer

Other

1.0 or less

HS-CAN+

PCM

Under any
condition:



Inspect for
continuity to
PCM.



Inspect for
continuity to
instrument
cluster.

Continuity detected -

Under any
condition:

2007 Mazda MX-5 Miata Sport

2007 ACCESSORIES & BODY, CAB Security and Locks (Advanced Keyless System) - MX-5 Miata

Microsoft

Thursday, July 09, 2009 3:36:54 PM

Page 40

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы:

Похожие инструкции для MX-5 Miata Sport 2007

Бренды по названию

Популярные бренды

Mazda MX-5 Miata Sport 2007, Руководство пользователя

Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы:

Похожие инструкции для MX-5 Miata Sport 2007

Бренды по названию

Популярные бренды