Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 170

Страница: 170 / 2244

1. Remove the door trim. (See

DOOR TRIM REMOVAL/INSTALLATION

2. Remove the screws, then remove the inner handle.

3. Detach the cables from the inner handle and door lock knob.

4. Install in the reverse order of removal.

Fig. 17: Identifying Inner Handle And Cable

Courtesy of MAZDA MOTORS CORP.

OPEN HOOK REMOVAL/INSTALLATION[ADVANCED KEYLESS SYSTEM]

1. Remove the following parts:

1. Console (See

CONSOLE REMOVAL/INSTALLATION

2. Quarter trim (See

QUARTER TRIM REMOVAL/INSTALLATION

3. Scuff plate (See

SCUFF PLATE REMOVAL/INSTALLATION

4. Tire house trim (See

TIRE HOUSE TRIM REMOVAL/INSTALLATION

5. Aeroboard (See

AEROBOARD REMOVAL/INSTALLATION

6. Seat back bar garnish (See

SEAT BACK BAR GARNISH REMOVAL/INSTALLATION

7. Back trim (See

BACK TRIM REMOVAL/INSTALLATION

8. Seat back bar lower garnish (See

SEAT BACK BAR LOWER GARNISH

REMOVAL/INSTALLATION

2. Remove the bolts.

3. Remove the open hook.

4. Install in the reverse order of removal.

2007 Mazda MX-5 Miata Sport

2007 ACCESSORIES & BODY, CAB Security and Locks (Advanced Keyless System) - MX-5 Miata

Microsoft

Thursday, July 09, 2009 3:36:54 PM

Page 11

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы:

Похожие инструкции для MX-5 Miata Sport 2007

Бренды по названию

Популярные бренды

Mazda MX-5 Miata Sport 2007, Руководство пользователя

Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы:

Похожие инструкции для MX-5 Miata Sport 2007

Бренды по названию

Популярные бренды