Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 1445

Страница: 1445 / 2244

3. Adjust the magnetic clutch clearance. (See

MAGNETIC CLUTCH ADJUSTMENT

BOLT REMOVAL/INSTALLATION NOTE

1. When removing or installing the bolt, hold the pressure plate as shown in

Fig. 10

Fig. 10: Removing/Installing Bolt

Courtesy of MAZDA MOTORS CORP.

SNAP RING REMOVAL/INSTALLATION NOTE

1. Remove the snap ring using a snap ring pliers.

2007 Mazda MX-5 Miata Sport

2007 HVAC Control System - MX-5 Miata

Microsoft

Thursday, July 09, 2009 2:27:32 PM

Page 11

«
...
1443
1444
1445
1446
1447
...
»

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы:

Похожие инструкции для MX-5 Miata Sport 2007

Бренды по названию

Популярные бренды

Mazda MX-5 Miata Sport 2007, Руководство пользователя

Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы:

Похожие инструкции для MX-5 Miata Sport 2007

Бренды по названию

Популярные бренды