manualshive.com logo in svg

Mazda MX-5 Miata Sport 2007, Руководство пользователя, Страница: 1270 / 2244

Поделиться
Скачать
Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 1270

2. Remove the bolts A, B and C. (See 

BOLT B, C INSTALL NOTE

.)  

3. Remove the junction. (See 

SEAT BACK CROSSMEMBER ASSEMBLY 

REMOVAL/INSTALLATION

 .)  

4. Loosen the installation bolts and nuts of the seat back crossmember component, and tilt the seat back 

crossmember component towards the vehicle front. (See 

SEAT BACK CROSSMEMBER ASSEMBLY 

REMOVAL/INSTALLATION

 .) 

Fig. 100: Identifying Power Retractable Hardtop Link Bracket And Bolts With Torque 
Specifications

 

Courtesy of MAZDA MOTORS CORP.

 

5. Rotate the power retractable hardtop link bracket in the direction shown by the arrow at the pivot fulcrum 

of pin A and set the hook out of the way.  

6. Remove the power retractable hardtop link bracket.  

7. Install in the reverse order of removal.  

Fig. 101: Rotating Power Retractable Hardtop Link Bracket

 

Courtesy of MAZDA MOTORS CORP.

 

 

2007 Mazda MX-5 Miata Sport 

2007 ACCESSORIES & BODY, CAB Exterior Trim - MX-5 Miata

  

Microsoft 

 

Thursday, July 09, 2009 3:32:13 PM

Page 70 

© 2005 Mitchell Repair Information Company, LLC. 

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов