manualshive.com logo in svg

Mazda MX-5 Miata Sport 2007, Руководство пользователя, Страница: 1507 / 2244

Поделиться
Скачать
Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 1507

CHECK CODE 22

 

Check 

code 22

Fuel level signal

STEP

INSPECTION CONDITION

DISPLAY

ACTION

1

Select check code 22 with the fuel gauge sender 
unit connector disconnected.

Go to the next 
step.

Except above

Go to the Step 6.

2

Connect terminals 2R and 2T of the instrument 
cluster.

Go to the next 
step.

Except above

Go to the Step 6.

3

Using the 

SST

 (Fuel and thermometer checker) 

or resistor, input 

20 ohms

 between instrument 

cluster terminals 2R and 2T.

Go to the next 
step.

Except above

Go to the Step 6.

4

Using the 

SST

 (Fuel and thermometer checker) 

or resistor, input 

60 ohms

 between instrument 

cluster terminals 2R and 2T.

Go to the next 
step.

Except above

Go to the Step 6.

5

Using the 

SST

 (Fuel and thermometer checker) 

or resistor, input 

100 ohms

 between instrument 

cluster terminals 2R and 2T.

Inspect the fuel 
gauge sender 
unit.

Except above

Go to the next 

step.

Inspect the wiring harness and connector between instrument cluster and fuel gauge sender 
unit. 

 

2007 Mazda MX-5 Miata Sport 

2007 ACCESSORIES & BODY, CAB Instrumentation-Driver Info - MX-5 Miata

  

Microsoft 

 

Thursday, July 09, 2009 3:30:27 PM

Page 19 

© 2005 Mitchell Repair Information Company, LLC. 

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов