Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 1776 | Manualshive

Страница: 1776 / 2244

background image

Fig. 37: Putting Steering Rack Into Gear Housing

Courtesy of MAZDA MOTORS CORP.

4. Using a press, press-in the oil seal (gear housing side) and inner guide until the press-in force increases

rapidly.

OIL SEAL (HOLDER SIDE), HOLDER ASSEMBLY NOTE

1. Apply multi-purpose grease to the oil seal holder side)

2. Install the plastic bag to the steering rack end so as not to damage the oil seal (holder side) and install the

oil seal (holder side) to the seal. Move the oil seal (holder side) together with the plastic bag so that they
pass the steering rack end, then remove the plastic bag.

3. Install the holder and move the steering rack until it contacts the housing.

2007 Mazda MX-5 Miata Sport

2007 STEERING Power Steering - MX-5 Miata

Microsoft

Thursday, July 09, 2009 2:11:38 PM

Page 38

© 2005 Mitchell Repair Information Company, LLC.

«
...
1774
1775
1776
1777
1778
...
»

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MX-5 Miata Sport 2007

Бренд: Taffio Страницы: 8

1973 Crown Hardtop

Бренд: Toyota Страницы: 50

Бренд: AC Schnitzer Страницы: 20

Бренд: Maserati Страницы: 210

Бренд: OnStar Страницы: 22

Vantage 12 Series

Бренд: Ecco Страницы: 5

v.LOGiC Intelligent Solution V5-NTG46

Бренд: Caraudio-Systems Страницы: 18

Бренд: Ford Страницы: 256

PRIME DESIGN URX-001-E

Бренд: Safe Fleet Страницы: 8

Бренд: Beper Страницы: 52

2013 GMC Savana

Бренд: GMC Страницы: 398

Бренд: Power Acoustik Страницы: 4

Бренд: JBL Страницы: 12

Бренд: A-Tach Mounts Страницы: 2

Portable Car Umbrella

Бренд: Mynew Страницы: 5

Бренд: Toyota Страницы: 36

Бренд: Scion Страницы: 58

Бренд: Yakima Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды