Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 1588

Страница: 1588 / 2244

Fig. 49: Attaching Double-Sided Adhesive Tape To Rear Trim

Courtesy of MAZDA MOTORS CORP.

REAR SIDE TRIM REMOVAL/INSTALLATION

EXCEPT POWER RETRACTABLE HARDTOP

1. Remove the following parts:

1. Console (See

CONSOLE REMOVAL/INSTALLATION

2. Quarter trim (See

QUARTER TRIM REMOVAL/INSTALLATION

3. Scuff plate (See

SCUFF PLATE REMOVAL/INSTALLATION

4. Tire house trim (See

TIRE HOUSE TRIM REMOVAL/INSTALLATION

5. Aeroboard (See

AEROBOARD REMOVAL/INSTALLATION

6. Front seat back bar garnish (See

SEAT BACK BAR GARNISH

REMOVAL/INSTALLATION

7. Back trim (See

BACK TRIM REMOVAL/INSTALLATION

8. Seat belt set plate (See

SEAT BELT REMOVAL/INSTALLATION

9. Seat back crossmember assembly (See

SEAT BACK CROSSMEMBER ASSEMBLY

REMOVAL/INSTALLATION

2. Remove the fasteners.

3. Pull the rear side trim outward and detach pins A, B and tab C.

4. Remove the rear side trim.

2007 Mazda MX-5 Miata Sport

2007 ACCESSORIES & BODY, CAB Interior Trim - MX-5 Miata

Microsoft

Thursday, July 09, 2009 3:29:26 PM

Page 47

«
...
1586
1587
1588
1589
1590
...
»

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы:

Похожие инструкции для MX-5 Miata Sport 2007

Бренды по названию

Популярные бренды

Mazda MX-5 Miata Sport 2007, Руководство пользователя

Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы:

Похожие инструкции для MX-5 Miata Sport 2007

Бренды по названию

Популярные бренды