Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 353 | Manualshive

Страница: 353 / 2244

background image

Fig. 52: Connecting SSTs (Deployment Tool) To SSTs (Adapter Harness)

Courtesy of MAZDA MOTORS CORP.

10. Press the activation switch on the

SST

(Deployment tool) connected with 49 L066 002 (a yellow

connector) of the

SST

(Adapter harness), and

after 3 s

, press the activation switch on the other

SST

(Deployment tool) to operate (deploy) the air bag module (both inflators).

WARNING:



Verify that air bag module operation (explosive) sound occurs
twice. If no operation (explosive) sound was heard or a single
operation (explosive) sound was heard, both inflators would
not have operated (deployed) properly. This may cause serious
injury if the air bag module operates (deploy) unexpectedly. If
the two operation (explosive) sounds are not heard, perform
Step 8 again. If a total of two operation (explosive) sounds
cannot be verified even though Step 8 is performed again,
leave the air bag module alone for 30 min or more before
approaching it again.



The air bag module is very hot immediately after it is operated
(deployed). You can be burned. Do not touch the air bag
module for at least 15 min after deployment.

2007 Mazda MX-5 Miata Sport

2007 RESTRAINTS Air Bag System - MX-5 Miata

Microsoft

Thursday, July 09, 2009 2:12:56 PM

Page 53

© 2005 Mitchell Repair Information Company, LLC.

«
...
351
352
353
354
355
...
»

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MX-5 Miata Sport 2007

Porsche 911 Turbo S Wheel

Бренд: FANATEC Страницы: 9

2011 grand cherokee

Бренд: Jeep Страницы: 22

2013 Grand Cherokee

Бренд: Jeep Страницы: 704

Бренд: Jeep Страницы: 558

Бренд: PAC Страницы: 4

Бренд: PAC Страницы: 4

Бренд: PAC Страницы: 8

Бренд: PAC Страницы: 5

Бренд: Ultra Start Страницы: 8

Бренд: Daewoo Страницы: 68

Бренд: Hyundai Страницы: 437

Бренд: Romik Страницы: 6

Бренд: Brodit Страницы: 2

Бренд: Power Fist Страницы: 12

Бренд: EAL Страницы: 7

Бренд: Actia Страницы: 37

Бренд: WABCO Страницы: 48

Бренд: CITROËN Страницы: 301

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды