Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 460

Страница: 460 / 2244

Fig. 147: Measuring Free Length Of Piston Return Spring

4. Inspect the lining of all drive plates. (C2)



If the lining is flaking or has changed color, or if it is worn or the print mark is wearing away,
replace it with a new drive plate.



When replacing, inspect the contact surfaces between the retaining plate, driven plate and drive
plate.



If they are scratched or have changed color, replace with new parts.

5. Inspect the lining of all drive plates. (C3)



If the lining is flaking or has changed color, or if it is worn or the print mark is wearing away,
replace it with a new drive plate.



When replacing, inspect the contact surfaces between the retaining plate, driven plate and drive
plate.



If they are scratched or have changed color, replace with new parts.

NOTE:



Before replacing with new drive plates, soak them at least 2 h in
ATF.

Fig. 148: Identifying Print Mark On Drive Plates (C2)

NOTE:



Before replacing with new drive plates, soak them at least 2 h in

2007 Mazda MX-5 Miata Sport

2006-08 TRANSMISSION Automatic Transmission Overhaul - MX-5 Miata & RX-8

Microsoft

Thursday, July 09, 2009 1:42:24 PM

Page 64

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы:

Похожие инструкции для MX-5 Miata Sport 2007

Бренды по названию

Популярные бренды

Mazda MX-5 Miata Sport 2007, Руководство пользователя

Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы:

Похожие инструкции для MX-5 Miata Sport 2007

Бренды по названию

Популярные бренды