Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 130

Страница: 130 / 2244

ABS_VOLT
(System battery
voltage value)



Ignition switch at
ON:



Approx. 12.2 V



Idling:

Approx.

14.1 V

Inspect the power
supply circuit.
(See

ABS SYSTEM

INSPECTION

ABSLF_I
(Left front inlet
solenoid valve
output state)

On/Off



Solenoid valve
activated: On



Solenoid valve
not activated:
Off

Inspect the ABS
HU/CM.
(See

ABS HU/CM

INSPECTION

ABSLF_O
(Left front outlet
solenoid valve
output state)

On/Off



Solenoid valve
activated: On



Solenoid valve
not activated:
Off

Inspect the ABS
HU/CM.
(See

ABS HU/CM

INSPECTION

ABSLR_I
(Left rear inlet
solenoid valve
output state)

On/Off



Solenoid valve
activated: On



Solenoid valve
not activated:
Off

Inspect the ABS
HU/CM.
(See

ABS HU/CM

INSPECTION

ABSLR_O
(Left rear outlet
solenoid valve
output state)

On/Off



Solenoid valve
activated: On



Solenoid valve
not activated:
Off

Inspect the ABS
HU/CM.
(See

ABS HU/CM

INSPECTION

ABSPMPRLY
(Motor relay output
state)

On/Off



Relay activated:
On



Relay not
activated: Off

Inspect the ABS
HU/CM.
(See

ABS HU/CM

INSPECTION

ABSRF_I
(Right front inlet
solenoid valve
output state)

On/Off



Solenoid valve
activated: On



Solenoid valve
not activated:
Off

Inspect the ABS
HU/CM.
(See

ABS HU/CM

INSPECTION

ABSRF_O
(Right front outlet
solenoid valve
output state)

On/Off



Solenoid valve
activated: On



Solenoid valve
not activated:
Off

Inspect the ABS
HU/CM.
(See

ABS HU/CM

INSPECTION

ABSRR_I
(Right rear inlet



Solenoid valve
activated: On

Inspect the ABS
HU/CM.

2007 Mazda MX-5 Miata Sport

2007 BRAKES On-Board Diagnostic (ABS) - MX-5 Miata

Microsoft

Thursday, July 09, 2009 3:17:55 PM

Page 8

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы:

Похожие инструкции для MX-5 Miata Sport 2007

Бренды по названию

Популярные бренды

Mazda MX-5 Miata Sport 2007, Руководство пользователя

Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы:

Похожие инструкции для MX-5 Miata Sport 2007

Бренды по названию

Популярные бренды