Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 140

Страница: 140 / 2244

GROUND FOR OPEN
CIRCUIT



Turn the ignition
switch off.



Inspect for continuity
between ABS HU/CM
terminal A (harness-
side) and ground.



Is there continuity?

Repair or replace the wiring harness for
open circuit between ABS HU/CM
terminal A and ground, then go to Step
5.

VERIFY PUMP MOTOR
OPERATION



Turn the ignition
switch off.



Connect the M-MDS
to the DLC-2.



Turn the ignition
switch to the ON
position (engine off).



Access PMP_MOTOR
active command
modes using M-MDS.



Does the pump motor
operate?

Yes

Go to the next step.

Replace the ABS HU/CM, then go to
the next step.
(See

ABS HU/CM

REMOVAL/INSTALLATION

VERIFY
TROUBLESHOOTING
COMPLETED



Make sure to
reconnect all
disconnected
connectors.



Clear the DTC from
the memory.



(See

CLEARING

DTCS
PROCEDURES



Start the engine and
drive the vehicle at

km/h {6.2 mph} or
more.



Gradually slow down
and stop the vehicle.

Yes

Replace the ABS HU/CM, then go to
the next step.
(See

ABS HU/CM

REMOVAL/INSTALLATION

Go to the next step.

2007 Mazda MX-5 Miata Sport

2007 BRAKES On-Board Diagnostic (ABS) - MX-5 Miata

Microsoft

Thursday, July 09, 2009 3:17:55 PM

Page 18

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы:

Похожие инструкции для MX-5 Miata Sport 2007

Бренды по названию

Популярные бренды

Mazda MX-5 Miata Sport 2007, Руководство пользователя

Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы:

Похожие инструкции для MX-5 Miata Sport 2007

Бренды по названию

Популярные бренды